Hook up amplifiers

hook up amplifiers

How do you hook up an amp to a car?

Have an amp that has good fuses in it. Then, hook your ground wire to the ground hook up on your amp. There are many different ways to run wires through you car so your on your own! Step 3: Hook Up Power Wire. You then hook up the power wire to the power hook up!

How to connect an amplifier to an audio system?

The RCA cable will be used to connect the amplifier to the audio unit, which can be your mobile phone or computer. Media player is said to be the input device, from which you will play your playlist or tracks on your amplifier. The screwdriver will be used to tighten and loosen the screws of the cable input ports.

How do I connect two amps to one preamp?

In that case, you can connect the pass-through outputs on your first amp to the preamp inputs on your second amplifier, and so on. If your head unit doesn’t have multiple preamp outputs, and your amps don’t have pass-through functionality, you’ll need to use Y adapters to split the signal between your amps.

How to connect a car amplifier to a 12V power supply?

Unscrew the 12V screw, put the other end of the wire in the 12V port and tighten the screw. Now, when you have connected the remote wires with the power wires, you must connect the power wires in the power input port of the car amplifier. To do so, take the yellow wire and insert it in the 12V port.

How do you hook up a car AMP to a battery?

Connect the amps negative terminal to the cars chassis ground. Use a short negative power wire that is the same diameter as the positive wire that leads to the battery. Insert the main power wire fuse once all the connections for the other wires are in place.

What kind of wiring do you need for a car amplifier?

Car amplifiers dont come with any wiring included. You must supply the amps power and ground wiring, an inline fuse, a remote turn-on wire, RCA cables, and speaker wires. The power and ground wires need to be thick enough to accommodate the amps demand for electrical current or the amp wont operate properly or put out its rated power.

How to mount an amp to a car stereo?

You’ll need to drill holes in the floor of your car to hold your mount in place. Once you’ve installed the mount, remove the stereo head and wire your amp into your car’s firewall, which is the metal panel between the engine and the interior. You’ll also need to wire any speakers you want to hook up to your amp later on.

Can I use a computer power supply for a car AMP?

Using an ATX (desktop computer) power supply for a car amp isn’t hard usually. It’s a matter of a few steps: Power connections: Cut several ground wires (black) and +12V wires (yellow) and strip them for about 3/8″ to 1/2″ bare wire.

How do you connect a 12 volt amp to a car?

Connect the 12 V+ and remote ports on the amp with the 2 in (5.1 cm) wire. The remote port on the amplifier allows it to turn on when you start your vehicle, but the remote port needs a 12 V wire attached to it if you use a computer power supply. Use the second 2 in (5.1 cm) piece of 18-gauge wire you cut earlier to connect to the remote port.

Can I use a computer power supply for a car AMP?

Using an ATX (desktop computer) power supply for a car amp isn’t hard usually. It’s a matter of a few steps: Power connections: Cut several ground wires (black) and +12V wires (yellow) and strip them for about 3/8″ to 1/2″ bare wire.

How to connect a car amplifier to a car?

Once you’ve connected the +12V and ground wiring then ground the “supply on” wire the supply should start up and your car amplifier should power on. There are some cases where you could have a problem, however. NOTE: If you’re using a high amount of current be sure to use all or nearly all of the yellow +12V wires to connect to the amp.

Can I use an ATX power supply for a car AMP?

Using an ATX (desktop computer) power supply for a car amp isn’t hard – in fact, you only need a few steps: Power connections: Cut the +12V wires (yellow) and the same number of ground (black) wires. Strip the insulation to leave about 3/8″ to 1/2″ bare wire.

Related posts: